3com 09-1632-000 User Manual

http://www.3com.com/ Getting Started with the OfficeConnect ® NETBuilder ® 10 Bridge/Router Part No. 09-1632-000Published May 1999 OC10.book Page 1

10 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTERThis step is necessary to establish the connection between your NMS and the OfficeConnect

Preconfiguration Set Up 11web-based information), a navigation frame, and a main window. The navigation frame lets you select from the Web Link basic f

12 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTERConfiguration ProcedureThis section provides step by step instructions for configuring the

Configuration Procedure 13 Configuring Dynamic Dial Configuring Network Addressing for Your Network: If your network uses the IP protocol, use the pro

14 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTERg In the start field, click the arrow and choose 2.2.h In the LocalDialNo field, enter the

Configuration Procedure 154 To manually enter SPID values, follow these steps:a In the Dial On Demand ISDN Setup section of the navigation frame, click

16 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTER7 Logically assign the two ISDN paths to port 4. a In the Dial On Demand ISDN Setup secti

Configuration Procedure 17b In the start field, click the arrow and choose 2.1.c In the LocalDialNo field, enter the local dial number string in quotes.

18 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTERd Click Apply.5 Enable all paths on port 4. a In the Dial On Demand ISDN Setup section of

Configuration Procedure 192 Add the phone number of the other site (Office B) to the dial number list. a In the Dial on Demand Dynamic Dial section of t

3Com Corporation 5400 Bayfront Plaza Santa Clara, California 95052-8145 Copyright © 1999, 3Com Corporation. All rights reserved. No

20 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTER5 Enable dynamic dial on the port. a In the Dial on Demand Dynamic Dial section of the na

Configuration Procedure 21c Click Apply.4 Assign an IP address to your routing ports. a In the Basic IP section of the navigation frame, click the IP N

22 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTERc Click Apply.10 Add a default route to port 4 to tell the OfficeConnect NETBuilder bridge

Configuration Procedure 23Configuring IPX Network Addressing Use this procedure when you use IPX as your network protocol. If you use IP as your network

24 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTERf In the CONTrol field, choose ROute.g Click Apply.Configuring PPP Authentication To configu

Configuration Procedure 25b In the AuthRemoteUser field, enter the username and password for office B (the office remote from you) in quotes. For example,

26 CONFIGURING YOUR OFFICECONNECT NETBUILDER 10 BRIDGE/ROUTERb In the AuthLocalUser field, enter the username and password for office B in quotes. For e

TECHNICAL SUPPORT3Com provides easy access to technical support information through a variety of services. This appendix describes these services.Info

28 TECHNICAL SUPPORT3Com Knowledgebase Web ServicesThis interactive tool contains technical product information compiled by 3Com expert technical engi

Support from Your Network Supplier 29Access by Digital ModemISDN users can dial in to the 3Com BBS using a digital modem for fast access up to 64 Kbps

C ONTENTS C ONFIGURING Y OUR O FFICE C ONNECT NETB UILDER 10 B RIDGE /R OUTER Prerequisites 6Preconfiguration Set Up 7Set Up the NMS as a

30 TECHNICAL SUPPORTIf you are unable to contact your network supplier, see the following section on how to contact 3Com.Support from 3ComIf you are u

Returning Products for Repair 31Returning Products for RepairBefore you send a product directly to 3Com for repair, you must first obtain an authorizat

To obtain an authorization number, call or fax:Country Telephone Number Fax NumberAsia, Pacific Rim +65 543 6500 +65 543 6348Europe, South Africa, and

3Com Corporation LIMITED WARRANTYOfficeConnect NETBuilder Bridge/RouterHARDWARE3Com warrants this hardware product to be free from defects in workmansh

Dead- or Defective-on-Arrival. In the event a product completely fails to function or exhibits a defect in materials or workmanship within the first

FCC CLASS A VERIFICATION STATEMENTWARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant t

FCC CLASS B STATEMENTThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1 This device may not ca

FCC DECLARATION OF CONFORMITYWe declare under our sole responsibility that the to which this declaration relates, is in conformity with the following

3COM END USER SOFTWARE LICENSE AGREEMENTIMPORTANT: Read Before Using This ProductYOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE U

from application to this License Agreement.LIMITED WARRANTY; LIMITATION OF LIABILITY: All warranties and limitations of liability applicable to the So

FCC C LASS B S TATEMENT FCC D ECLARATION OF C ONFORMITY 3C OM E ND U SER S OFTWARE L ICENSE A GREEMENT OC10.book Page 4 Thursday, May 13,

C ONFIGURING Y OUR O FFICE C ONNECT NETB UILDER 10 B RIDGE /R OUTER This guide contains the information you need to install and configure your Offi

6 C ONFIGURING Y OUR O FFICE C ONNECT NETB UILDER 10 B RIDGE /R OUTER The instructions in this guide describe how to configure Office A. After you’

Preconfiguration Set Up 7 Preconfiguration Set Up This section describes the things you need to do before performing the actual network configuration. S

8 C ONFIGURING Y OUR O FFICE C ONNECT NETB UILDER 10 B RIDGE /R OUTER Figure 3 OfficeConnect Back Panel Connectors Cable the Ethernet Connector

Preconfiguration Set Up 9 No leased line configuration is required. The OfficeConnect NETBuilder 10 bridge/router automatically configures the PPP connec