3com TR User Manual Page 84
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-2 CHAPTER 5: CONFIGURING WITH THE LCD CONSOLE
Bridge Configuration
Bridge settings can be made using the LCD console. If
you have made settings using the VT100 interface,
those settings will be reflected in the LCD console.
Refer to Chapter 3 for more information on navigat-
ing the LCD console.
Although many of the steps in the following proce-
dure are similar, be aware that the settings will vary
depending on the bridging environment you choose.
Refer to Chapter 1 for more information on the types
of bridging supported by the Switch 2000 TR.
NOTE: Some bridge settings (Spanning Tree) will not
take effect until the Switch 2000 TR is reset. Refer to
“Resetting the Switch 2000 TR in Chapter 3 for
instructions on resetting the Switch 2000 TR.
From the Switch 2000 TR LCD banner, proceed as fol-
lows:
1 Press [Enter].
Switch 2000 TR >Unit Id appears.
2 Press [Down Arrow] until Switch 2000 TR >Bridge
appears.
3 Press [Enter].
BRIDGE >Bridge Type appears.
4 Press [Enter].
Bridge Type:<SRT> appears.
5 Press [Down Arrow] to select bridge type. Choose
from:
■ SRT (Source Route Transparent)
■ Transparent Bridging
■ Source Route
6 Press [Enter] to select appropriate bridge type.
BRIDGE >Bridge Type appears.
7 Press [Down Arrow].
BRIDGE >Spanning Tree appears.
8 Press [Enter].
Spanning Tree: <802.1d> appears.
9 Press [Down Arrow] to select Spanning Tree type.
Choices:
■ 802.1d—IEEE 802.1d standard. This setting is typi-
cally used for Transparent bridging or Source Route
Transparent.
■ IBM—IBM Spanning Tree standard. This setting is
typically used in Source Routing environments.
■ Disabled—No Spanning Tree support.
10 Press [Enter].
11 Press [Left Arrow] to return to the higher-level screens
in the LCD console.
- Version 4.0 1
- ANAGEMENT 4
- VT100 I 5
- Related Publications 10
- About the SuperStack 11
- II Switch 2000 TR 11
- System Features 12
- Summary of Features 13
- 1-4 CHAPTER 1: OVERVIEW 14
- Ring Segmentation 15
- The Front Panel 16
- RJ-45 Ports 17
- Front Panel LEDs 17
- LCD Display Buttons 17
- The Rear Panel 18
- Optional Slide-In Modules 19
- The FDDI Module 20
- 1-12 CHAPTER 1: OVERVIEW 22
- SuperStack II Switch 1000 TX 23
- Token Ring Switching Concepts 24
- Transparent Bridging (TP) 25
- Spanning Tree 26
- Congestion Control 27
- Forwarding Modes 27
- 1-18 CHAPTER 1: OVERVIEW 28
- GETTING STARTED 29
- Considerations for Placement 30
- Configuration Guidelines 31
- Power Supply and Fuse 31
- Replacing the Fuse 31
- HAPTER 2: GETTING STARTED 32
- Installing the Switch 2000 TR 33
- Connecting to the Serial Port 34
- Device Defaults 34
- Stack Defaults 35
- Bridge Defaults 35
- SETTING UP FOR MANAGEMENT 37
- VT100 Management Interface 38
- Via the Serial Port 38
- Via an IP Network Connection 38
- Unit ID # 39
- Head Unit 39
- Managing over the Network 40
- Management Prerequisites 41
- Source Routing Prerequisites 42
- The VT100 Console 42
- Key Board Shortcuts 43
- Correcting Text Entries 44
- Default Users 44
- VT100 Console Menu Map 45
- Setting Up the VT100 Console 46
- ■ Device IP Address 47
- Unit Id. 1 49
- LCD Console Menu Map 50
- Setting Up BOOTP 52
- Setting Up BOOTP 3-17 53
- Auto Logout 54
- Upgrading Software 55
- Upgrading Module Software 56
- Resetting the Switch 2000 TR 57
- Reset Button 58
- Power Cycle Reset 58
- Quick Setup 60
- Bridge Configuration 61
- Setting Source Route Bridging 62
- Setting Transparent Bridging 62
- Spanning Tree Fields 63
- Port Configuration 64
- Setting Port Personality 65
- Setting Port Priorities 65
- Setting Congestion Control 65
- Setting Port Speed 66
- Setting Forwarding Mode 66
- Dynamic Cut-Thru Threshold% 66
- Port Bridge Configuration 68
- I/O Module Configuration 69
- Stack Configuration 69
- VLAN Configuration 70
- Unit Configuration 72
- Administrative Configuration 73
- Setting Local Security 74
- Creating New Users 75
- Deleting Users 75
- Database Entries 77
- Database Entry Methods 77
- Switch Database Configuration 78
- SNMP Trap Configuration 79
- Serial Port Configuration 80
- Serial Port Configuration 4-23 81
- > Port 85
- Setting Port State 86
- Setting Speed 86
- > I/O Module 88
- MONITORING THE SWITCH 2000 TR 89
- Unit Statistics 90
- Port Statistics 91
- Port Statistics (Traffic) 92
- Port Statistics 6-5 93
- Stack Status 94
- Status 6-7 95
- Fault Log 96
- Remote Polling (PING) 97
- LCD Status 98
- VIRTUAL LANS 99
- Benefits of VLANs 100
- VLANs and the Switch 2000 TR 101
- HAPTER 7: VIRTUAL LANS 102
- Switch 2000 TR 103
- 7-6 CHAPTER 7: VIRTUAL LANS 104
- SOFTWARE UPGRADE UTILITY 105
- S (address) 106
- M (subnet mask) 106
- Using the Commands 107
- Status Messages 108
- SCREEN ACCESS RIGHTS 109
- SERIAL PORT CABLE PIN-OUTS 111
- TROUBLESHOOTING 113
- PPENDIX D: TROUBLESHOOTING 114
- SWITCH 2000 TR 115
- SPECIFICATIONS 115
- TECHNICAL SUPPORT 117
- PPENDIX F: TECHNICAL SUPPORT 118
- Support from 3Com 119
- Returning Products for Repair 120
- LIMITED WARRANTY 125
- 764-5000 126
Related products and manuals for Computer Accessories 3com TR
Computer Accessories 3com 2924-PWR User Manual
(248 pages)
(248 pages)
Computer Accessories 3com 1000 User Manual
(152 pages)
(152 pages)
Computer Accessories 3com 3900 User Manual
(36 pages)
(36 pages)
© 2020, manymanuals.com. All rights reserved. | 0.279 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals